Fully sorted 1992 BMW 325is - $13,500.00. Open to offers but please don't low ball me. If I can't find the right buyer I'll either part it out or keep him to play with at Mission.
http://s418.photobucket.com/albums/pp264/jimmc8/Whitey/
Current SCCA & ICSCC logbooks
SCCA approved roll cage
Aprroximately 20 hours on the engine, no over-revs
Iron M52 block
84.5mm CP 12.5:1 cr pistons (.5mm overbore)
knifedged, lightened, balanced crank
Forged eagle rods
ARP head studs and main studs
head is ported and polished, valve job, etc.
supertech dual valve springs
new genuine BMW OE lifters
Sunbelt M3 sport cams
M50 intake
24# injectors
Riot racing BBTB
8mm vanos limited
Euro oil housing with AN oil cooler lines
Supersprint replica long tube headers
265 rwhp + 234# of torque on a MUSTANG dyno
Programable WAR Chip, Redline set at 7100 rpm
Bilstein PSS9 suspension
650# rear & 575# front springs
M3 Dinan Sway Bars
Reinforced Rear Subframe, Rear Sway Bar & Front Lower Subframe
Poly-urethane Front Lower Control Arm Bushing Kit
Euro M3 Headers, Racing Resonators & Supersprint Racing Muffler
Beemer tuning Cold Air Intake Kit
Beemer Tuning Short Shift Kit
3.64 LSD Diff, Rogue Diff Cover
Steel Braded Brake Lines
DTC-70 Brake Pads Front with cooling ducts
DTC-60 Brake Pads Rear
Lightweight Battery
Sparco EVO Race Seat (2) - Driver & Passenger - (FIA approved)
VAC Seat Base & slider
6 Point Harnesses (2) - Current date - (SFI/FIA approved)
Fire Suppression System
Wired for radios
Wheels - Kosei 16X7 with 225/50 BFG R1's - 12 HC
- Kosei 16X7 with 22/50 Hoosier R6 - 6 HC
- Kosei 16X7 with 210/610 Hankook Rains - 5 HC
- 1 Set - "Idon'tknow's, weigh about 20# per" with 225/50 Hoosier Wets - 6 HC
Sparco Deep Dish Stearing Wheel with Quick Release
Gauge cluster with Fuel Mixture, Oil Pressure, Oil Temp
HotLap Lap timer C/W beacon
Weight 2770 with 5 gallons of fuel + 180# driver
With current engine runs in ST & SPM
With an M50B25 swap meets RS, IP2 ITR & ITS with included 29MM SIR
Available - (Currently installed)
Aim Pista Data system with GPS Module, Brake and Throttle Sensors - $2,500
Weight Box (32#) + ballast (160#) - SCCA approved - $400
jimmcadie (at) gmail (.) com
(604) 828-9676
http://s418.photobucket.com/albums/pp264/jimmc8/Whitey/
Current SCCA & ICSCC logbooks
SCCA approved roll cage
Aprroximately 20 hours on the engine, no over-revs
Iron M52 block
84.5mm CP 12.5:1 cr pistons (.5mm overbore)
knifedged, lightened, balanced crank
Forged eagle rods
ARP head studs and main studs
head is ported and polished, valve job, etc.
supertech dual valve springs
new genuine BMW OE lifters
Sunbelt M3 sport cams
M50 intake
24# injectors
Riot racing BBTB
8mm vanos limited
Euro oil housing with AN oil cooler lines
Supersprint replica long tube headers
265 rwhp + 234# of torque on a MUSTANG dyno
Programable WAR Chip, Redline set at 7100 rpm
Bilstein PSS9 suspension
650# rear & 575# front springs
M3 Dinan Sway Bars
Reinforced Rear Subframe, Rear Sway Bar & Front Lower Subframe
Poly-urethane Front Lower Control Arm Bushing Kit
Euro M3 Headers, Racing Resonators & Supersprint Racing Muffler
Beemer tuning Cold Air Intake Kit
Beemer Tuning Short Shift Kit
3.64 LSD Diff, Rogue Diff Cover
Steel Braded Brake Lines
DTC-70 Brake Pads Front with cooling ducts
DTC-60 Brake Pads Rear
Lightweight Battery
Sparco EVO Race Seat (2) - Driver & Passenger - (FIA approved)
VAC Seat Base & slider
6 Point Harnesses (2) - Current date - (SFI/FIA approved)
Fire Suppression System
Wired for radios
Wheels - Kosei 16X7 with 225/50 BFG R1's - 12 HC
- Kosei 16X7 with 22/50 Hoosier R6 - 6 HC
- Kosei 16X7 with 210/610 Hankook Rains - 5 HC
- 1 Set - "Idon'tknow's, weigh about 20# per" with 225/50 Hoosier Wets - 6 HC
Sparco Deep Dish Stearing Wheel with Quick Release
Gauge cluster with Fuel Mixture, Oil Pressure, Oil Temp
HotLap Lap timer C/W beacon
Weight 2770 with 5 gallons of fuel + 180# driver
With current engine runs in ST & SPM
With an M50B25 swap meets RS, IP2 ITR & ITS with included 29MM SIR
Available - (Currently installed)
Aim Pista Data system with GPS Module, Brake and Throttle Sensors - $2,500
Weight Box (32#) + ballast (160#) - SCCA approved - $400
jimmcadie (at) gmail (.) com
(604) 828-9676
